Bob, please don't misunderstand ... it is nice, but I didn't build it.(That's the promo shot for the plans)
| Official Luthiers Forum! http://www-.luthiersforum.com/forum/ |
|
| 6x48 edge sander? http://www-.luthiersforum.com/forum/viewtopic.php?f=10101&t=44309 |
Page 1 of 1 |
| Author: | meddlingfool [ Wed Oct 08, 2014 8:50 pm ] |
| Post subject: | 6x48 edge sander? |
Is there such a thing? Grizzley's is discontinued, but it sure would be handy... |
|
| Author: | Clay S. [ Wed Oct 08, 2014 9:01 pm ] |
| Post subject: | Re: 6x48 edge sander? |
The 6X80 edge sander would be much handier. Get the one with the tilting table, not the one with the wraparound table. |
|
| Author: | Bri [ Wed Oct 08, 2014 9:06 pm ] |
| Post subject: | Re: 6x48 edge sander? |
I Think both King and General make one. Oddly I just saw this on our local classifieds. http://classifieds.castanet.net/details ... TL0.mailto B |
|
| Author: | meddlingfool [ Wed Oct 08, 2014 9:12 pm ] |
| Post subject: | Re: 6x48 edge sander? |
I have a 6x 89 already. Hoping to drag into the big machine room and replace it with a smaller footprint machine in the RH room... |
|
| Author: | meddlingfool [ Wed Oct 08, 2014 9:15 pm ] |
| Post subject: | Re: 6x48 edge sander? |
Looking for one with the belt at right angle to the floor.. |
|
| Author: | Dave Stewart [ Thu Oct 09, 2014 9:23 am ] |
| Post subject: | Re: 6x48 edge sander? |
You could always consider building one. Attachment: plansnow edge sander.jpg http://plansnow.com/dn3079.html |
|
| Author: | dnf777 [ Thu Oct 09, 2014 9:27 am ] |
| Post subject: | Re: 6x48 edge sander? |
Grizzly makes an 80" edge sander that has an optional radius-ing attachment for fretboards I've been eyeing. Have you looked at that one? Whole thing with radius jib is around 800. |
|
| Author: | Bobc [ Thu Oct 09, 2014 9:43 am ] |
| Post subject: | Re: 6x48 edge sander? |
WOW Dave That is really nice. |
|
| Author: | Dave Stewart [ Thu Oct 09, 2014 9:51 am ] |
| Post subject: | Re: 6x48 edge sander? |
| Bob, please don't misunderstand ... it is nice, but I didn't build it. (That's the promo shot for the plans) |
|
| Author: | Bobc [ Thu Oct 09, 2014 10:56 am ] |
| Post subject: | Re: 6x48 edge sander? |
Dave Stewart wrote: :) Bob, please don't misunderstand ... it is nice, but I didn't build it. (That's the promo shot for the plans) Oh I was hoping you could give us some pointers. 
|
|
| Author: | meddlingfool [ Thu Oct 09, 2014 1:21 pm ] |
| Post subject: | Re: 6x48 edge sander? |
I think that what it will come down to. The shopfox w1717 is pretty close, but I don't see it as being worth 600$. So I've had a crazy scheme, I'll post pics later.... |
|
| Author: | Haans [ Fri Oct 10, 2014 6:50 am ] |
| Post subject: | Re: 6x48 edge sander? |
Dave, that archtop is lovely! |
|
| Author: | Dave Stewart [ Fri Oct 10, 2014 3:40 pm ] |
| Post subject: | Re: 6x48 edge sander? |
I appreciate that Haans. You and your instruments are an inspiration to many. Cheers! |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|